Posted on

Set up Instruction for Hid Conversion Kits

HID Conversion Kits could possibly be unlawful in some states and are offered for off street or demonstrate use only. Test with your regional BMV for a lot more data.
Useful Information and Set up Guidelines:

  • Do not contact the HID bulb. If you do contact the bulb through set up, clean with alcoholic beverages.
  • Do not glance straight into the bulb when it is turned on as it might induce long-lasting damage to your eyes.
  • Headlights ought to be adequately modified just after set up. HID bulbs are much brighter than halogen bulbs. By not changing your headlights, you might lower the visibility of oncoming traffic thanks to glare. If you do not know how to change your headlights, please check with a qualified.
  • Do not fall or implement inappropriate/needless drive to your HID parts as executing so might induce damage to them. If any damage is learned, discontinue use and speak to your retailer. Do not use the procedure till the problem is solved, in purchase to avoid probable electrical-shock or fire.
  • The HID procedure generates 23000volts when activated. Do not use damp or oily fingers when installing or inspecting the procedure. Or you might be subjected to severe burns or electrical-shock.
  • Make sure all connectors and wires are secured and absent from any very hot surfaces. Wires that are unfastened or resting against a very hot surface might induce electrical dangers.
  • Do not switch on the bulb around flammable materials when it is outside of headlight housing.
  • Do not switch lights on/off promptly. Carrying out so might lower the lifespan of your bulbs.
  • Do not put in HID procedure in any housing with cracks. Moister might damage the bulb or induce electrical-shock.
  • Before last set up pre-exam all the parts. Assure compatibility by plugging in all the wires and turning the procedure on.

Notice: Unique adapters, connectors, modules or harness might be essential to the right way put in the HID procedure on some vehicles. Make sure you have every thing essential for your motor vehicle. BMW, Mercedes, Audi, Dodge/Chrysler and Volkswagen are only a handful of that might require exclusive set up supplies.
One Beam Set up Instructions:

  1. Confirm that the HID Conversion Package you gained have all the ingredient essential for the set up (A checklist of ingredient readily available down below)
  2. Disconnect the car battery.
  3. Take out the factory light bulbs. If your vehicle’s headlights have dust caps, please clear away them as well.
  4. If your motor vehicle is outfitted with headlight dust caps, drill a one”(24mm) gap to accommodate the wiring harness.
  5. Take out the xenon HID bulb from the protective casing. Be thorough NOT to contact the bulb. Take care of it by its plastic foundation. If any grease or filth will get on the bulb wipe clean with rubbing alcoholic beverages.
  6. Put the bulb’s wiring harness by the dust cap (as illustrated).
  7. Insert the xenon HID bulb into your headlight and secure it.
  8. Link the spade terminals (positive & negative) to the factory headlight wiring harness.
  9. Insert the rubber boot (on the wiring harness) by the gap on the dust cap (which you drilled earlier).
  10. Link the bulb to the ballast. The brief release will “click on” after totally secured.
  11. Obtain a mounting site for the ballast. Use the ballast bracket, screws or zip-ties as essential. Notice: Do not drill holes on the ballast box, mount absent from moving parts and mount to a secure site.
  12. Test your vehicle’s headlight fuse. Make sure it is rated at 20amps or increased. Swap the fuse with a 20amp fuse if your headlight fuse is of a decreased rating.
  13.  Reconnect the battery cables.
  14. Turn light swap on and let your new xenon light to operate for 10 minutes.

Bi-Xenon Set up Instructions:
Wiring Diagram

  1. Confirm that the HID Conversion Package you gained have all the ingredient essential for the set up (A checklist of ingredient readily available down below)
  2. Cleanse all connectors and wipe the HID bulbs and connectors with rubbing alcoholic beverages
  3. Install the HID bulbs into the headlight housing
  4. Link the HID bulbs to the ballast (2 spherical brief-disconnects)
  5. Link the higher beam command wires (tiny rectangular connectors)
  6. Link the ballasts to the Hello/Lo wiring harness (oval connectors with yellow rubber seals)
  7. Link the three-pin socket on the wiring harness to One of the headlight sockets
  8. Link the thick pink wire to the battery positive
  9. Link the thick black wires to the battery negative or floor
  10. Mount the ballast and clean up the wiring harness with zip ties
  11. Obtain a mounting site for the ballast. Use the ballast bracket, screws or zip-ties as essential. Notice: Do not drill holes on the ballast box, mount absent from moving parts and mount to a secure site.
  12. Turn headlight swap on and let your new xenon light to operate for 10 minutes

Altering Your Very low Beam Headlight:

  1. Park on a stage surface 20 toes driving a further car and switch on your minimal beam headlights.
  2. Make sure the lower-off of the beam is just earlier mentioned the bumper of the car in front. (You should refer to the graphic down below)
  3. To make sure the two headlights are even modified, please switch on the headlights straight against a flat wall 20 toes absent and change lights till the lower-offs of two headlight line up.

Troubleshooting:
Flickering through pre-exam or bulb out warning: Some vehicles evaluate the resistance of the bulb connecting into the factory socket. Given that the Xenon ballast does not use any resistance when lights the bulbs, the vehicles personal computer thinks there is something completely wrong, when there really is not. It will then start off to flicker the HID kit and might exhibit a bulb out warning. To solution this, an automotive HID bulb out resistor ought to be used, or a bulb out warning module.
One Beam HID Conversion Package Factors:

  • HID Xenon Bulbs (with wires) Two (2) parts
  • HID Ballasts Two (2) parts
  • Bracket(s)/Screw(s)/Other Mounting Accessories One (one) set
  • Set up Handbook One (one) piece

Bi-Xenon HID Conversion Package Factors:

  • HID Xenon Bi-Xenon Bulbs (with wires) Two (2) parts
  • HID Ballasts Two (2) parts
  • Hello/Very low Beam Manage Wiring Harness One (one) piece
  • Bracket(s)/Screw(s)/Other Mounting Accessories One (one) set
  • Set up Handbook One (one) piece

***Some products might fluctuate from 1 producer to a further***
This Set up tutorial is written for the HID Conversion Kits shown earlier mentioned. Some kits could possibly have to have added steps that are not shown below. Get in touch with your supplier for a lot more data.